MPD-830R - Boser MPD-830R 300W DC-DC ATX Power Supply Simple Type: Power...
- Part Number:
- MPD-830R
- Model Number:
- MPD-830R
- Make:
- BOSER
- Lead Time:
- Available
- Qty In Stock:
- Available
Boser MPD-830R 300W DC-DC ATX Power Supply Simple Type: Power Supply
Boser MPD-830R 300W power supply DC/DC
For Resellers and High Volume Orders:
Please request a quote to obtain preferred pricing.
Features
- None Available
Specifications
- 3.5" Floppy Driver: AMP 171822-4 or equivalent
- Altitude: Will operate properly at any altitude between 0 to 10,000ft
- ATX: Molex 39-01-2200 or equivalent
- DC Connectors: 3 positions terminal blocks
- Dimensions: 14.0 x 15.0 x 8.62 cm; Tolerance specified is +/-0.4mm between mounting holes and +/-0.8mm for other dimmensions
- Disk Drive: AMP 1-480424-0 or equivalent
- Efficiency: The efficency is higher than 65% while measuring at nominal line and rated load
- EMI: EM55022 (1998) / EN55011 (1999)
- EMS: IEC 61000-4-2 / IEC 61000-4-3 / IEC 61000-4-4
- Humidity: The power supply can operate from 5% humidity to 95% humidity non-condensing at 40°C
- Input Current: The maximum input current is 5A at 110VDC input
- Input Voltage: The range of input voltage is from 72~136VDC
- Inrush Current: Will not exceed 10A at 110VDC input cold start, 25°C
- Line Regulation: The output line regulation for each output is less than +/-1% while measuring at rated load and -40~-72VDC input voltage changing
- Load Range: At factory, all outputs in 60% rated load condition; the +5V output is set to between 4.80V and 5.20V. The other outputs are checked to be within the specified voltage accuracy range
- Load Regulation: The output voltage load regulation is less than the values in the following table by changing each output load +/-40% from 60% from rated load, and keep other outputs at 60% rated load
- Output Power: The total DC continuous power shall be kept within 300W ambient temperature of 40°C below, and input voltage at 110VDC. The maximum, total combined output power on the 3.3V and 5V rails is 150W
- P4: Molex 39-01-2045 or equivalent
- Power Fail Signal: The power fail signal will fall at least 1ms before any of the output voltages lower than the regulation limits
- Power Good Signal: When power start-up, the power good signal will increase between 100ms to 500ms after all output DC voltages are within regulation limits
- Power On Signal: This TTL compatible signal (active low) is use to switch ON the main output. When power on is disconnected from secondary common, all outputs except +5Vsb shall turn off
- Protection Over Voltage: For some reasons the power supply might fail to control itself, the build-in crowbar circuit will automatically shut down the outputs to avoid damaging the external circuits. The trip point of O.V.P. circuit is around 5.7V to 7.0V
- Ripple And Noise: The peak to peak ripple and noise for +5V, +3.3V outputs are less than 50mV, and for the other output are less than 100mV at rated load. Measuring is done by 15MHz bandwidth limited oscilloscope and terminated each output with a 0.47uF capacitor electrolysis capacitor at rated load, nominal line
- Safety: EN 60950
- Short Circuit: The power supply will go into hiccup mode function against short circuit or over load conditions. If the faults condition removed, the power supply will restart automatically
- Temperature: 0~+70°C, -20°C can start up, derating from 50°C (operating); -40~+75°C (storage)
Applications
- None Available
Aliases
- None Available
Related Items
MPD-810H
Boser MPD-810H 120W 10~30VDC DC-DC ATX Open Frame Power Supply
MPD-810H-V
Boser MPD-810H-V 120W 30~120VDC DC-DC ATX Open Frame Power Supply
BPW-8410
80W 48V DC-DC open frame power supply with Input Range:
BPW-8410
80W 48V DC-DC Open Frame Power Supply Input Range: 36~72VDC