MPI-815H - Boser MPI-815H 150W AC-DC ATX Open Frame Power Aupply Simple...
- Part Number:
- MPI-815H
- Model Number:
- MPI-815H
- Make:
- BOSER
- Lead Time:
- Available
- Qty In Stock:
- Available
Boser MPI-815H 150W AC-DC ATX Open Frame Power Aupply Simple Type: Power Supply
MPI-815H 150W open frame power supply from Boser.
For Resellers and High Volume Orders:
Please request a quote to obtain preferred pricing.
Features
- None Available
Specifications
- Altitude: 0~10,000ft
- Dimensions: 19.8 x 9.7 x 4.0 cm
- Efficiency: The efficiency is higher than 70% while measuring at nominal line and rated load
- EMI: FCC docket 20780 curve B / EN55022B
- EMS: IEC-61000-4-2 Level 3 8KV air discharge, Level 2 4KV contact discharge / IEC 61000-4-3 Level 3 10V/M / IEC 61000-4-4 Level 3 2KV / IEC 61000-4-5 Level 3 2KV / IEC61000-4-6 Level 3 10V / IEC 61000-4-8 Level 3 10A/M / IEC 61000-4-11
- Hold Up Time: The hold up time is longer than 16mS at 115VAC input and rated load
- Humidity: 10~90% non-condensing
- Input Current: 2A at 115VAC or 1.5A at 230VAC max.
- Input Frequency: 47~63Hz
- Input Voltage: 85~264VAC
- Inrush Current: The maximum inrush current is 6A at 115VAC or 3A at 230VAC
- Line Regulation: The line regulation is less than +/-1% at rated load with +/-10% change in input voltage
- Load Range: At the factory, the +5V output is set between 5.08~5.13V and all output at 60% rated load, and the other output is checked to be within the accuracy range. The maximum total combined output power on the 3.3V and 5V rails is 90W. The maximum load cannot be exceed 150W
- Load Regulation: The load regulation for +5V is less than +/-2%, for +12V is less than +/-5%, for +3.3 and -12V is less than +/-5% while the measuring is done by changing the measured output loading +/-40% from 60% rated load, and keep other output is at 60% rated load
- Over Temp. Protection: When the power supply operating over the temperature limit, the power supply will be shut down automatically to protect itself
- PFC: IEC 61000-3-2 / IEC 61000-3-3
- Power Fail Signal: The pwoer fail signal will go low at least 1ms before any of the output voltages fall below the regulation limits
- Power Good Signal: The power is turned on, the power good signal will go high between 100ms to 500ms after all output DC voltage are within regulation limits
- Power On/Off: The power supply will be turned on when the power On/Off pin is connected to secondary GND
- Protection: The power supply will generate the hiccup mode to protect itself against short circuit or over load condition, and will return to normal after wrong condition is removed. The power supply has over voltage protection function
- Ripple And Noise: The peak to peak ripple and noise for +5V, 3.3V output are less 50mV for +5Vsb for +5Vsb is 100mV, for +12V is less than 100mV, for -12V is less than 150mV at ranted load and nominal input, which is measured by a 15MHz bandwidth limited oscilloscope and the each output is connected with a 0.47uF capacitor
- Safety: UL 60950 / CSA 22.2 No. 234 / VDE EN60950
- Temperature: 0~+50°C (operating); -20~+70°C (storage)
Applications
- None Available
Aliases
- None Available
Related Items
FSP180-50PLA
Boser FSP180-50PLA - Power Supply | 1U High | 180W
ZKS-250WX
Boser ZKS-250WX 250W AC-DC ATX Power Supply supports ATX2.03
ZKS-400WX-A
Boser ZKS-400WX-A 400W AC-DC ATX Power Supply supports ATX2.03
MPI-925A
Boser MPI-925A Power Supply. 250W | AC-DC AT | >65%